Mastercraft drill press manual

Page Position the table and workpiece Fig. Always place a piece of backup material 1 wood, plywood, etc. This will prevent splintering on the underside of the workpiece as the drill bit breaks through. To keep the material from spinning out of control, it must contact the left side 3 of the column as illustrated, or be clamped 4; not included to the table.

Note: For small workpieces that cannot be clamped to the table, use a drill press vise not included. The vise must be clamped or bolted to the table to avoid injury. To drill a hole: 1. Mark where. Line the drill bit tip up- with the mark. P the workpiece in place, 3.

Turn ON the bench drill press and pull down on the feed handles with appropriate force needed to allow the drill bit to drill material. Practice with scrap material to get the feel of the machine before attempting to do any drilling operation. To stop the drill bit at a pre-measured depth: 1. Rotate the upper depth knob 2 until the bottom of the knob is aligned with the desired depth mark 5 on the gauge scale.

Rotate the depth scale lock knob 1 until it meets the lower depth scale knob 2. The chuck will stop after travelling downward to the selected distance.

To adjust quill return height Fig. Turn the feed handles until the quill is at the desired height and hold it there.

Rotate the lower depth knob 3 until it rests against the bottom of the metal gauge support 4. Depth scale method Fig. Put the workpiece on the table, and raise the table until the tip of the drill bit just touches the top of the workpiece. Lock the table in place. Determine the drill depth for this workpiece. Rotate the upper depth lock knob 1 until it meets the lower depth knob 2.

The chuck will be stopped at the distance selected on the depth scale. Workpiece method Fig. With the bench drill press in the OFF position, bring the drill bit 6 down until the tip is even with the mark.

Holding the feed handles at this position, rotate the lower depth knob 2 until it meets the metal support. Rotate the upper 1 depth scale lock knob until it meets the lower knob 2. The chuck and the drill bit will now be stopped at the distance selected on the depth scale. Mechanical variable speed Fig. To increase or decrease the speed when operating, raise or lower the speed handle 1.

Use the following table to determine the recommended speed for the drill size you are using and the type of material you are to drill. While drilling, check the speed on the digital speed readout 2 located at the front of the drill press. Vacuum sawdust or metal shavings that accumulates in and on the motor, pulley housing, table, and work surface. Apply a light coat of paste wax to the column and table to help keep these surfaces clean and Page17 rust-tree.

The ball bearings in the spindle and the V-belt pulley assembly are greased and pen:nanently sealed. Lubricate the table bracket and locking knobs if they become difficult to use. Auservlclngofthedrill press should be pei:tormed by a qualified service technician. The drill bit burns or smokes. Excessive drill run-out or wobble, drilled hole. Drill bit binds in the workpiece. Spindle returns too slowly or too quickly. Chuck falls off spindle. Incorrect belt ten;ion.

Dry spindle. Loose spindle pulley. Loose motor pulley. Dull drill bit. Not lubricated. Bent drill bit. Worn spindle bearings. Take to a qualified service technician. See the bit. Excessive feed pressure. The workpiece is 1. Defective or damaged power cord. Motor will not run. Tum breaker. Low voltage. Use another circuit or have a qualified electrician upgrade the service.

Motor will not start 1. Overloaded circuit. Improper extension cord. Short circuit in motor. Description Qty Key No. Not withstanding the foregoing, this limited warranty does not cover any damage that has resulted from abuse or misuse of the Merchandise. This warranty does give you specific legal rights and you may have other rights, which vary from state to state.

Be careful, tools are dangerous if improperly used or maintained. Any oral representation s made will not be binding on seller or its employees. The rights under this limited warranty are to the original purchaser of the merchandise and may not be transferred to any subsequent owner. This limited warranty is in lieu of all warranties, expressed or implied including warranties or merchantability and fitness for a particular purpose.

Seller shall not be liable for any special, incidental, or consequential damages. The sole exclusive remedy against the seller will be for the replacement of any defects as provided herein, as long as the seller is willing or able to replace this product or is willing to refund the purchase price as provided above.

For insurance purposes seller is not allowed to demonstrate any of these power tools for you. Leave a Reply Cancel reply. Previous Previous post: Leviton plug in lamp dimmer. MasterCraft Grinder Maximum Instruction manual 22 pages. MasterCraft Heater Instruction manual 13 pages.

MasterCraft Heater Instruction manual 6 pages. MasterCraft Impact Driver Instruction manual 14 pages. MasterCraft Impact Driver Owner's manual 30 pages. MasterCraft Impact Driver Instruction manual 11 pages.

MasterCraft Impact Driver Owner's manual 25 pages. MasterCraft Impact Driver Owner's manual 20 pages. MasterCraft Impact Driver Owner's manual 22 pages. MasterCraft Impact Driver Instruction manual 12 pages. MasterCraft Impact Driver Operating manual 12 pages. MasterCraft Impact Driver Owner's manual 21 pages. MasterCraft Indoor Furnishing Instruction manual 36 pages. MasterCraft Indoor Furnishing Instruction manual 32 pages. MasterCraft Indoor Furnishing Instruction manual 27 pages.

MasterCraft Indoor Furnishing Instruction manual 16 pages. MasterCraft MO Manuals. MasterCraft Laser Level Instruction manual 12 pages. MasterCraft Lathe Instruction manual 14 pages. MasterCraft Lathe Owner's manual 18 pages. MasterCraft PU Manuals. MasterCraft HS Manuals. MasterCraft HV Manuals. MasterCraft Measuring Instruments Instruction manual 2 pages. MasterCraft Multimeter Instruction manual 72 pages. MasterCraft Multimeter Instruction manual 48 pages.

MasterCraft Multimeter Instruction manual 40 pages. MasterCraft Multimeter Instruction manual 44 pages. MasterCraft Multimeter Instruction manual 14 pages.

MasterCraft Nail Gun Instruction manual 29 pages. MasterCraft Nail Gun Instruction manual 30 pages. MasterCraft Nail Gun Instruction manual 32 pages. MasterCraft Nail Gun Operating manual 15 pages. MasterCraft Paint Sprayer Instruction manual 27 pages.

MasterCraft Paint Sprayer Operating manual 15 pages. MasterCraft Planer Instruction manual 14 pages. MasterCraft Planer Owner's manual 28 pages. MasterCraft Power Screwdriver Instruction manual 21 pages. MasterCraft Power Screwdriver Owner's manual 17 pages. MasterCraft Power Screwdriver Instruction manual 20 pages.

Drill the appropriate size holes. The jig is shipped fully assembled except for the two hand levers. Screw the If alignment Hitachi Power Tools. Patent No. UPC No. Internal Socket of the Drill Chuck. Capacities: Steel. Capacities: Wood. Capacities: Aluminum. Hammer Drills. Rubber Mallet or Hammer. Flat Head Screwdriver Exterior Caulk Paintable Commercial Security Products.

ISSUE Electronic Update September Strike the keying tool once firmly with a hammer to shear all four pins at the shear line. Strike the keying tool With thousands of repair parts, diagrams and parts lists, we have everything you need to get your RIDGID tools back to work. Additionally for skirting boards and profiles: power drill.

Careful subfloor preparation is essential for an Pure Click 40 is an LVT floor, designed for use in residential areas. Do not use a hammer to put planks together.